Limited Availability ›
This product has limited availability. It will be replaced by: CS241DM. Some accessories, replacement parts, or services may still be available when it is no longer available.
CS240DM Sensor für die Temperatur der Modulrückwand, PT-1000 Klasse A mit digitaler Modbus RS-485 Ausgabe
Genauigkeit Klasse A bei jeder Kabellänge
wetter  wasser  energie  gas flux and turbulence  bauwerke  boden


Der CS240DM ist ein smarter PRT (Platin-Widerstands- Temperatur) Sensor, den man an der Rückwand eines PV-Moduls anbringen kann. The CS240DM includes a new Campbell Scientific precision analog-to-digital, smart-sensor module that makes back-of-module temperature measurements that are among the most accurate measurements available today. The module, based on CR1000X design, is optimized for the Class A PRT and minimizes self-heating and lead-wire resistance. Measurement electronics are surge protected, include 1200 V isolation, and are environmentally protected with a rugged over-molding featuring an IP65 rating. Data is differentially transmitted in twisted-pair cabling, which is well suited for industrial energy applications with excellent noise rejection and high voltage, NEC Outdoor, UV, UL, and NEC ratings.

Lesen Sie mehr

Funktionen und Vorteile

  • Best-in-class measurement accuracy and technology
  • Modbus RTU RS-485 digital serial communications
  • Precision Pt1000 Class A sensing element
  • Compliant with IEC 60751, DIN EN 60751
  • Meets 61724-1 PV System Performance Standard
  • Optional NIST traceable calibration certificate
  • Purchased with any cable length
  • Rugged design proven in more than 4,000 installations worldwide


CS240DM and cable (sold separately)
CS240DM and cable attached (sold separately)
CS240DM options
CS240DM mounted to the back of a solar panel module
Kapton tape (pn 11051) is required for cable strain relief. The tape is also used to fasten the sensor to the back of a solar panel when the temperature may exceed 70°C.

Technische Beschreibung

The CS240DM consists of a Pt-1000 Class A PRT encased in an aluminum disk. The disk protects the PRT, particularly during installation when pulled through conduit, and promotes heat transfer from the surface while minimizing convective heat loss to the surroundings. An adhesive tab on the disk fastens the CS240DM to the measurement surface. If the temperature may exceed 70°C, Kapton tape is also required to secure the probe.

The precision analog-to-digital, smart-sensor module is based on the CR1000X. The module design is optimized for the Class A PRT that minimizes self-heating and lead-wire resistance. Measurement electronics are surge protected, include 1200 V isolation, and are environmentally protected with a rugged over-molding featuring an IP65 rating. Data is differentially transmitted in cabling that is well suited for industrial energy applications with excellent noise rejection and high voltage, NEC outdoor, UV, UL, and NEC ratings.

The CS240DM provides PV stakeholders with highly accurate back-of-module temperature—even at long cable lengths—for use in power-performance modeling and simulation of solar energy applications. Back-of-module temperature is critical for any evaluation of effective irradiance and power conversion.


Sensor Platinum resistive thermometer (PRT)
System Uncertainty ±0.3°C
Disk Material Anodized aluminum
Surge Protection 1200 V isolation
Supply Voltage of the Sensor 5 to 30 Vdc
Power Draw 15 mA
Compliance Information
  • UL AWM 2586 1000V 105°C approval
  • CSA AWM 600V 105°C FT approval
Conforms with Electromagnetic Compatibility Directive (EMC)
Conforms with the Restriction of Hazardous Substances Directive (RoHS2)
Disk Diameter 2.54 cm (1.0 in.)
Overall Probe Length 6.35 cm (2.5 in.)
Overmolded Joint Dimensions 5.72 x 1.12 x 1.47 cm (2.25 x 0.44 x 0.58 in.)
Weight 90.7 g with 3.2 m cable (0.2 lb with 10.5 ft cable)

Sensing Element

Precision 1000 ohm Class A platinum sensing element (Pt-1000)
Accuracy ±(0.15 + 0.002T)°C
Temperature Coefficient of Resistance TCR = 3850 ppm/K
Long-Term Stability Maximum Ro drift 0.04% (after 1000 h at 400°C)
Operating Temperature Range -40° to +135°C


Protocol Modbus RTU protocol (over RS-485)
Format 8 data bits, 1 stop bit, even parity as default (user-configurable)
Baud Rate 19,200 bps as default (user-configurable)
Modbus ID Last two digits of serial number as default (user-configurable)


  • High-flex construction with jacket for pulling through conduit
  • Weld spatter and oil resistant
Jacket Material Black semi-gloss PVC, UL VW-1 sunlight resistant for outdoor use
Agency Approvals
  • UL AWM Style 2463
  • NEC/CEC CMX outdoor
Nominal Wire Diameter 0.61 mm (0.024 in.)

FAQs für

Number of FAQs related to CS240DM: 4

Alle anzeigenWenige anzeigen

  1. A hot spot is caused if a cell in series is under-producing due to shading and gets reversed bias due to the other producing cells. For bifacial modules, as long as the front face is not shaded, all the cells should be producing and covering a small area on the back side and should not cause a severe mismatch.

  2. Even when three-pt calibration isn’t ordered, when we build the probes, we perform a final test to verify that they are reading within 0.3°C of our calibrated reference sensor at room temperature.

  3. NIST traceability provides an assurance of accuracy. This is especially desirable in accordance with IEC 61724, which is a solar energy generation monitoring specification that requires calibrated sensors.

Aufgelistet unter

Common Accessory for the following products: