Standardgehäuse / ENC16/18
ENC16/18 Enclosure, 457 x 406 x 228 mm
Robust und vielseitig
Campbell Komponenen lassen sich einfach und schnell montieren
wetter wasser energie gas flux and turbulence bauwerke boden

Überblick

Das Enc16/18 ist ein 40,6cm breites und 45,7cm hohes wetterfestes Gehäuse. Es ist das größte unserer gehäuse und kann einen Logger, eine Stromversorgung und Peripheriegeräte aufnehmen. Es wird für Anwendugne empfohlen, wo mehrere Geräte wie Multiplexer oder Modems eingebaut werden müssen.

Lesen Sie mehr

Funktionen und Vorteile

  • Wasserdicht zum Schutz der Instrumente
  • Rückwand so ausgelegt, dass Komponenten von Campbell Scientific leicht und sicher montiert werden können
  • Weisse, UV-stabile Gehäuse reflektieren die Sonnenstrahlen und reduzieren so Temperaturgradienten im Gehäuse ohne dass ein weiterer Strahlungsschutz nötig ist

Bilder

Technische Beschreibung

The ENC16/18's backplate is prepunched with half-inch-on-center holes suitable for attaching a data logger, power supply, and a communications or measurement and control peripheral.

This enclosure is shipped with the 7363 enclosure supply kit that consists of desiccant, a humidity indicator card, cable ties, wire tie tabs, putty, grommets, screws, and PVC coupling. Additionally, Campbell Scientific offers a CS210 Enclosure Humidity Sensor for monitoring relative humidity inside of the enclosure. (See Ordering Info on the web page.)

Spezifikationen

Color White (Reflects solar radiation, reducing temperature gradients inside the enclosure without using a separate radiation shield.)
Construction Fiberglass-reinforced polyester enclosure with door gasket, external grounding lug, stainless-steel hinge, and lockable hasps
Enclosure Classification NEMA 4X (before being modified for cable entry)
Number of Cable-Entry Seals 2 large, 2 medium, 2 small
Dimensions
  • 45.7 x 40.6 x 22.9 cm (18 x 16 x 9 in.) internal
  • 43.82 x 38.74 x 25.22 cm (17.25 x 15.25 x 9.93 in.) internal under the lid space
  • 49.53 x 44.4 x 26.98 cm (19.5 x 17.48 x 10.62 in.) external
Weight 7.7 kg (17 lb)

Kompatibel mit

Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.

Datenlogger

Product Compatible Note
CR1000 (retired)
CR200X (retired)
CR216X (retired)
CR300
CR3000
CR5000 (retired)
CR6
CR800
CR850
CR9000X (retired)

Additional Compatibility Information

The -VC cable opening option is required to fit a BP84 84-Ahr power supply in the ENC16/18 (see Ordering Info).


FAQs für

Number of FAQs related to ENC16/18: 18

Alle anzeigenWenige anzeigen

  1. If you purchased a Stahlin enclosure from Campbell Scientific and it has a failed gasket, we can help you. We will need you to provide an image of the failed gasket, verify the size of your enclosure, and provide your contact information. We can then arrange to have a replacement gasket sent to you from Stahlin. For assistance, contact Technical Support at 435.227.9100.

  2. The ENC16/18 weighs 17 lb. Its internal dimensions are 16 x 18 x 9 in.
  3. Most likely, yes. The datalogger is protected against electrical noise, and 60 Hz filtering can be selected in many sensor measurements to filter out the effects of 60 Hz noise.

  4. Yes. Use a standard electrical box and outlet.
  5. Our fiberglass enclosures can withstand very cold locations, and their fiberglass/plastic construction is very resistant to corrosion.
  6. The terminals do not need to be replaced. Just sand or file the corrosion away, exposing clean copper, and the fittings will continue to be functional.
  7. It depends on the device. Most devices have built-in mounting flanges, but some items require a separate mounting bracket.
  8. The following information is applicable to many of Campbell Scientific’s standard enclosures and prewired enclosures.

    Note: The procedure below will not work for torn or damaged seals.

    To make a field repair to a loose gasket on an enclosure, first acquire an adhesive, such as standard Gorilla Glue, that is rated for use with polyurethane foam. The adhesive should be compatible with, and recommended for, use with polyurethane foam. Follow these steps:

    1. Pull the gasket away from the gasket channel, being careful not to tear the gasket. The gasket does not need to be removed completely. Rather, remove only those areas that have pulled loose on their own. To keep the gasket up out of the way, lay a small object (such as a toothpick, pen, or pencil) horizontally across the channel.
    2. Using an adhesive that is rated for use with polyurethane foam, apply a small bead of adhesive to the gasket channel. Because the adhesive’s only function is to keep the gasket in place, use it sparingly.
    3. Remove any objects that were holding the gasket out of the way.
    4. Carefully place the gasket in the gasket channel.
    5. Wait 1 to 3 hours for the adhesive to cure before closing the door.