Datenkabel / SC105
SC105 CS I/O to 9-Pin RS-232 DCE Synchronous Interface
Adapter für CSI/O Port
wetter wasser energie gas flux and turbulence bauwerke boden

Überblick

Das SC105 Interface ermöglicht Kommunikation zwischen einem Campbell Datenlogger und einem RS232 DCE Gerät. Es wird z.B. zum Anschluss des COM110 Modems am CSI/O-Port verwendet, es können aber auch Geräte von Drittanbietern angeschlossen werden. Das SC105 ist kompatibel mit allen Loggern, die einem CSI/O-Port haben.

Lesen Sie mehr

Funktionen und Vorteile

  • Supports communication between a data logger and an RS-232 DCE device
  • Communicates at baud rates up to 115.2 kbps
  • Provides internal buffering capability to ensure no data is lost during transmission
  • Data logger can operate at a different baud rate than the DCE device
  • No power source needed—powered by the datalogger and computer
  • Compatible with most Campbell Scientific data loggers
  • Helps protect components from electrical damage
  • Ships with cables needed for most uses

Bilder

Technische Beschreibung

The SC105 provides internal buffering that temporarily stores data. This buffering allows the datalogger and DCE device to operate at different baud rates by storing the data received from the faster device until the slower device is ready to receive it. Internal buffering also ensures that no data is lost during transmission.

Spezifikationen

Baud Rates Supported 1200, 9600, 19200, 38400, 57600, 115200 bps
RS-232 Parity Supported Even, odd, none
RS-232 Data Bits Supported 7, 8
CS I/O Port Modes CSDC, SDC, ME, Addressed Print Device for P96 output
Power Requirements Data logger’s 5 V supply
Current Drain
  • Up to 8 mA of additional current may be used by the DCE device connected to the SC105.
  • 0.16 mA (standby)
  • 1 to 4 mA (communicating)
Operating Temperature Range
  • -25° to +50ºC (standard)
  • -55° to +85°C (extended)
Operating Relative Humidity up to 95% (non-condensing)
Dimensions 2.3 x 4.3 x 9.2 cm (0.9 x 1.7 x 3.6 in.)
Weight 45.4 g (1.6 oz)

Kompatibel mit

Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.

Datenlogger

Product Compatible Note
CR1000 (retired)
CR200X (retired)
CR216X (retired)
CR3000
CR5000 (retired)
CR6
CR800
CR850
CR9000X (retired)

Additional Compatibility Information

Cable Connections and Mounts

Three cables (13657 Null Modem Cable, SC12 CS I/O Data Cable, and 10873 Serial Data Cable) are shipped with the SC105. The 13657 cable is used to program the device via a computer. The SC12 cable connects the SC105 to the data logger, and the 10873 cable connects the SC105 to the RS-232 DCE device. An SC12R-6 cable (purchased separately) may be used instead of the SC12 cable if a longer cable is required.

The 16987 mounting kit is available for attaching the SC105 to the backplate of an environmental enclosure.

Data Logger Considerations

Note: When using an SC105 with OS version 4 or newer with a mixed-array data logger, the data logger operating system should be updated to the latest released version.

Dokumente

Übereinstimmung mit Richtlinien u. Vorschriften


Downloads

SC105 OS v.04 (573 KB) 28-08-2007

Current SC105 firmware. Requires the Device Configuration Utility and a 9-pin female to female NULL modem cable.
Liste der Änderungen

Device Configuration Utility v.2.22 (42.3 MB) 12-09-2019

A software utility used to download operating systems and set up Campbell Scientific hardware. Also will update PakBus Graph and the Network Planner if they have been installed previously by another Campbell Scientific software package.

Supported Operating Systems:

Windows 10, 8.1, 8, and 7 (Both 32 and 64 bit)

Liste der Änderungen

FAQs für

Number of FAQs related to SC105: 9

Alle anzeigenWenige anzeigen

  1. The SC105 uses the RS-232 standard, which is not compatible with multidrop communications (more than two devices on the same RS-232 bus). There are some third-party devices on the market that allow multiple devices to communicate over the same RS-232 link.

  2. Depending on what equipment is being used, a special interface may be required to attach a specific device to the datalogger’s CS I/O port. In general, devices with a CS I/O port can be attached directly to the datalogger’s CS I/O port. Devices with an RS-232 port require a special interface, such as the SC932A or SC105, to connect to the datalogger’s CS I/O port.

  3. Both the computer’s serial port and the SC105’s RS-232 port are configured as data terminal equipment (DTE) devices. Because both components are DTE, a null modem cable is needed between them.

  4. The SC105 needs to be connected to the data logger’s CS I/O port, either directly or with the included SC12 cable. The SC105’s RS-232 port needs to be connected to the PC’s serial port using the included null modem cable.

  5. Using an SC105 with a RavenXTV or RavenXTG cellular modem allows for the two devices to communicate at differing baud rates. It also allows for other devices, such as an RF401 radio or CR1000KD handheld display, to simultaneously be connected to the datalogger’s CS I/O port.

  6. The SC932A only is compatible with modem-enabled (ME) two-way communication between a datalogger and a modem. In contrast, the SC105 is compatible with both ME and Synchronous Device for Communication (SDC) communications, as well as having the ability to internally buffer data.

  7. An RS-232 device cannot be directly connected to the CS I/O port of the datalogger. A peripheral, such as an SC932A or SC105, is required.
  8. Most third-party modems require a null modem cable, SC105, SC110 cable, or SC932A to interface with a datalogger.  Many modems manufactured by Campbell Scientific can connect directly to a datalogger’s CS I/O port using an SC12 or serial cable.

Anwendungsbeispiele

Korea: Damage from Freezing Roads
Korea Expressway Corporation (KEC) was established in 1969 to construct and manage expressways throughout South......lesen Sie mehr

Aufgelistet unter