CDM-A116 16-Kanal 5 V Analogmultiplexer
24- bit Auflösung, schafft zusätzliche Sensorkapazitäten
wetter wasser energie gas flux and turbulence bauwerke boden

Überblick

Der CDM-A116 ist ein Analogmultiplexer zur einfachen Erweiterung eines Campbell-Datenloggersystems. Er enthält einen 24 bit Analog-Digitalwandler und ermöglicht Messungen mit sehr geringem Rauschen. Der CDM-A108 unterstützt auch Period-Average Messungen und kann Anregungsspannung und/oder Strom liefern.

Der CDM-A1116 hat 16 differentiale Eingänge und 4 Anregungskanäle. Man kann über zwei 12V-Port und zwei geschalteten 12V Port andere Geräte mit Strom versorgen, über 4 geschaltete 5V Ausgänge können Peripheriegeräte gesteuert werden. 

Lesen Sie mehr

Funktionen und Vorteile

  • Ability to make simultaneous measurements
  • CANbus 2.0A/2.0B capable; contact Campbell Scientific for details

Bilder

Front right tilt view
Front right tilt view
Front right tilt view
Front view
Back view
Left view
Right view
Top view
Bottom view
Using a screwdriver for wiring purposes

Technische Beschreibung

The CDM-A116 offers 24-bit sigma-delta Adc with 16 user programmable notch frequencies from 30,000 Hz to 2.5 Hz, including 50 and 60 Hz. Previous generations of data loggers could notch out 50 or 60 Hz.

Spezifikationen

-NOTE- Additional specifications are listed in the CDM-A108 and CDM-A116 brochure.
Mounting Standard 1-in. grid (DIN rail mounting available)
Operating Temperature
  • -40° to +70°C (standard)
  • -55° to +85°C (extended)
Power Requirements 9.6 to 32 Vdc voltage
Estimated Accuracy
  • ±(0.04% of reading + offset) 0° to 40°C
  • ±(0.06% of reading + offset) -40° to +70°C
  • ±(0.08% of reading + offset) -55° to +85°C
Number of Channels 16 differential or 32 single-ended inputs
Analog Inputs 32 single-ended or 16 differential (with ±5000 mV, ±1000 mV, ±200 mV ranges 24 bit ADC)
Maximum Multiplexed Sample Rate 3.0 kHz (using fast [100 μs] input setting)
Maximum Burst Sample Rate 30 kHz
Input Range ±5000 mV, ±1000 mV, and ±200 mV
Period Averaging Traditional period averaging on analog input channels
CPI For data logger connection. Baud rate selectable from 50 kbps to 1 Mbps. (Allowable cable length varies depending on baud rate, number of nodes, cable quality, and noise environment, but can be as long as 700 m under proper conditions.)
USB USB 2.0 full speed connection available for attaching to a PC. (Port is used to configure the module and download updates via our Device Configuration Utility.)
Warranty One year against defects in materials and workmanship
Dimensions 20.3 x 12.7 x 5.1 cm (8 x 5 x 2 in.)
Weight 0.9 kg (1.95 lb)

Typical Current Drain

Sleep <1 mA
Active 1 Hz Scan 2 mA (estimated)
Assumes one single-ended measurement with the first notch frequency (fN1) at 30 kHz
Active 20 Hz Scan 20 mA
Assumes one single-ended measurement with the first notch frequency (fN1) at 30 kHz

Voltage/Current Excitation Outputs

Voltage Excitation ±5 V (@ 50 mA)
Current Excitation ±2.5 mA (±5 V compliance voltage)
Number of Voltage/Current Excitation Outputs 4

General Purpose Outputs

Number of SW5V Outputs 4
SW5V Output Resistance 30 Ω
Number of SW12V Outputs 2
Typical Limit of SW12V Outputs 200 mA
Minimum Limit of SW12V Outputs 180 mA
Number of 12V Outputs 2
Typical Limit of 12V Outputs 200 mA
Minimum Limit of 12V Outputs 180 mA

Kompatibel mit

Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.

Datenlogger

Product Compatible Note
CR1000 To use the CDM-A116 with a CR1000 datalogger, an SC-CPI (data-logger-to-CPI interface) must be used between the data logger and the CDM-A116. 
CR1000X
CR300
CR3000 To use the CDM-A116 with a CR3000 datalogger, an SC-CPI (data-logger-to-CPI interface) must be used between the data logger and the CDM-A116. 
CR6
CR800 To use the CDM-A116 with a CR800 datalogger, an SC-CPI (data-logger-to-CPI interface) must be used between the data logger and the CDM-A116. 
CR850 To use the CDM-A116 with a CR850 datalogger, an SC-CPI (data-logger-to-CPI interface) must be used between the data logger and the CDM-A116. 

Miscellaneous

Product Compatible Note
CR310

Dokumente

Handbücher

Übereinstimmung mit Richtlinien u. Vorschriften


Downloads

CDM-A100 OS v.06 (612 KB) 05-09-2019

Execution of this download installs the CDM-A108 / CDM-A116 Operating System on your computer which can then be uploaded to the CDM-A108 or CDM-A116 device with the Device Configuration Utility.

Liste der Änderungen

CPI Calculator v.1.0 (2.49 MB) 06-07-2016

The CPI Calculator is a downloadable Microsoft Excel spreadsheet used to estimate the usage and capacity of a CPI network.  The calculator provides an overview on CPI devices including the CDM-A108, CDM-A116, CDM-VW300, CDM-VW305, and the CSAT3B.  The calculator can also estimate the measurement speed of the CDM-A108 and CDM-A116 based on the number of channels and measurement parameters.

 

The CPI Calculator is an estimation tool and will help you better understand and design CPI networks by considering the following:

  1. What is the capability of each CDM or CPI device
  2. What is the CPI network capacity
  3. How much of the CPI capacity are the CDMs or CPI devices using

 


Anwendungsbeispiele

Oklahoma Mesonet: Meteorological Network
The Oklahoma Mesonet is a statewide environmental monitoring network developed through the cooperative efforts of......lesen Sie mehr

Artikel und Pressemitteilungen