Das SC115 ist ein leichtes, tragbares 2-GB Gerät, das den Speicher eines Loggers erweitert oder mit dem Daten zwischen Logger und PC transportiert werden können. Es kann mt den neueren Loggern verwendet werden und ist der einzige externe Speicher, der mit dem CR800 und CR850 kompatibel ist.Lesen Sie mehr
The SC115 consists of electronics protected in a custom molded package. It has a USB 2.0 compatible connector for attaching it to the PC's USB port, and a CS I/O 9-pin connector for attaching it to a data logger's CS I/O port. The SC115 may be connected directly to a PC or data logger, or connected through the supplied extension cables.
The SC115 is typically used as an external data storage device, but may also be used as a USB-to-CS I/O synchronous device communications (SDC) adapter. As a USB-to-CS I/O adapter, the SC115 supports direct communication between a Campbell Scientific data logger and a PC equipped with a USB port. However, the SC115 is not electronically isolated, and therefore is better for temporary communications with a battery-powered PC. Another device, the SC-USB, also supports direct communications with a PC's USB port, but is optically isolated.
USB drivers for the SC115 must be installed before connecting the SC115 to a PC for configuration or as a USB-to-CS I/O adapter. The driver can be installed from the Device Configuration Utility device page by clicking the "Install the Device Driver" link.
|Storage Capacity||2 GB|
|Power Requirements||12 V (supplied through the PC’s USB port or the data logger’s CS I/O port)|
|Typical Current Drain||
|Temperature Range||-25° to +50°C|
|Packaging||Overmolded with thermoplastic polymide|
|Connectors||USB 2.0 compatible, CS I/O 9-pin|
|Dimensions||10.54 x 4.32 x 1.78 cm (4.15 x 1.7 x 0.7 in.)|
|Weight||63.79 g (2.25 oz)|
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
|CR5000 (retired)||Beginning with OS version 6, the SC115 is compatible with the CR5000.|
|CR9000X (retired)||Beginning with OS version 6, the SC115 is compatible with the CR9000X.|
The SC115 has a CS I/O port for attachment to the data logger and a USB port for attachment to a PC. You can connect the SC115 to the PC or data logger either directly or via the supplied cables. (Only one SC115 can be connected to a data logger at a time.) An SC12 CS I/O cable and a USB cable are shipped with the SC115.
CRBasic TableFile instruction is used to store data to the drive. Our Device Configuration (DevConfig) utility can be used for field configuration, OS download, and setting the SDC address. CRBasic and DevConfig are included in LoggerNet and PC400 Datalogger Support Software.
Windows USB drivers for the SC115 are installed via the Device Configuration Utililty. In the Device Configuration Utility, click on the link "install the device driver for the SC115" in the main body of text for the SC115.
Number of FAQs related to SC115: 8
Alle anzeigenWenige anzeigen
Yes, but the data storage must be managed by the program.
The SC115 works with any Campbell Scientific datalogger that has a CS I/O terminal.
The available storage can be augmented by adding an NL115 or a CFM100 with an industrial-grade CompactFlash memory card. An SC115 CS I/O-to-USB Flash Memory Drive can also be used.
On the Outputs page of the Short Cut program generator, each table has an option to send the data to an SC115.
The SC115 can be used in three ways:
When used as a memory device, the TableFile() instruction must be included in the program. The SC115 cannot be used as a USB-to-CS I/O adapter and as a memory storage device at the same time.
As long as the program running in the datalogger has the TableFile() instruction in at least one data table, the datalogger will automatically download the appropriate data to the SC115.